Temperature Control

Express Extractor Heater by BVV™ 1 Year Warranty, Built in house ready to ship in 24hrs! The BVV™ Extractor Heater is our built in house high power extractor heater circulator.  We have 3 model units 3,500, 8,000 & 11,000 WATTS!  Each upright panel comes with 25ft of silicone tubing and a 5 gallon reservoir.  Each system is capable of heating up to 140°F and can exceed the demand of even the largest extraction vessels.  The system operates on an independent nitrile diaphragm pump circulating water @1.5GPM.  The pump can self prime up to 11ft. and within a typical extractor this pump is operating around 30-50psi in circulating pressure.     BVV Part# KW AMPS Voltage Breaker AMPS Installed Plug Rec. Wire Size Temp. Range EEH-3.5KW 3.5 29 120V (1x30)A L5-30P Plug 10 AWG 120°F EEH-8KW 7.3 33 240V (1x40)A 6-50P 8 AWG 80-140°F (adjustable) EEH-11KW 11 46 240V (2x30)A 6-30P (2x12) AWG 80-140°F (adjustable) EEH-5.5KW 5.5 25 220V (1X25)A 6-30P  10 AWG     The 3.5KW unit has a digital temperature display and cannot be adjusted from the standard factory programmed 120°F.  During normal recovery operations used with our extractors this fluctuates between 120-157°F.   Though there is a lack in temperature accuracy we measure at the extractor base a consistent recovery temperature around 122-125°F. These heater are built with an electrical failsafe that prevents them from operating dry, and will auto shut down if the flow is unexpectedly stopped to protect the unit.  The attached in-line filter will prevent any debris from entering the heater.  A clogged filter will also prevent the heater from operating.     General Extractor Size Heater Recommendations for these Models 0-2lbs Biomass EEH-3.5KW 2-5lbs Biomass EEH-8KW 5-20lbs Biomass EEH-11KW      At BVV our favorite model is the 11KW.  The unit does require two 240V 30A Single phase circuits, but its now a permanent fixture in or laboratory.   Every model will pump out lots of heat for any recovery situation, could you use a 3.5KW heater on a 5 or 10lb unit?  Absolutely, Just expect longer times to reach the heaters maximum setting.   For example we heated 3x 6"x48" fully jacketed columns to 140°F (heater temp) in about 11 minutes using the 11KW heater.   Another example is a 1lb Apollo extractor with a fully jacketed collection base heated to 120°F in about 8-9 min. using the 3.5KW extractor heater.    ETL Listed to UL 499 and CSA (Canada) Utilizing all UL approved components for the heater, pump, and emergency stop switches, wiring harnesses, plugs, and electrical housings.  The heater arrive with the specified plugs attached, however all of the models can be hardwired directly if you choose not to use a plug.  *240V units can be used on 208V single phase with 25% reduced temperature output Express Extractor Heater Quick Start Guide

Read more less

NEOCISION 20L Chiller (-40c) - ETL Rated     Product Name Circulating Chiller Model NEO20L-40 Reservoir volume L) 20L Refrigeration performance No-load minimum temperature (℃) A: ﹣ 20℃ ( Customizable: ﹣ 30℃ / C: ﹣ 40℃ Best operating temperature (℃) A: ﹣ 20℃ ~ 20℃B: ﹣ 30℃ ~ 20℃C: ﹣ 40℃ ~ 20℃ Best operating environment (℃) ≤30 Environmental relative humidity (%RH) ≤65 Cooling capacity at -40 ℃ kw 0.7 Refrigerant R404A Electrical performance Cooling unit power (W) 1500 Sensor pt100 Controller, monitor liquid crystal Computer interface R485 optional safety protection Compressor delay protection, machine leakage,over-current, over-voltage protection Power AC230V±10%/60HZ Pump Power (W) 15 Maximum flow (L/min) 10 Maximum lift (m) 2.5 Liquid inlet and outlet pipe diameter (mm) φ18 Whole machinefunction Total Weight (Kg) 105 Tank opening/depth ( mm) φ300mm*300mm Out size (mm) 420*580*790 Adaptation rotary evaporator (volume* number) 10L*2 Note The equipment can be customized to different supply voltage frequency; different flow head external circulation system and external magnetic stirring device.         TEMP: Displays the measured temperature value. To set the desired temperature, press the setting key until the TEMP SET value flashes. Press the setting key again to confirm the parameter. SET: Displays the desired temperature value set manually. RUN: Indicates that the chiller is operating. Cooling Indicator: Appears when the chiller is cooling. Circulation Indicator: Appears when the pump is operating. TIME: Displays the set running time; this value countdowns to zero and operation stops. To set a timer, press the setting key. When the TIME value flashes, enter the desired time using they arrow keys. Leave at zero if a timer is not needed. Silence Indicator: Appears when an alarm has been silenced. Alarm Indicator: It will appear when there is an alarm. Settings: Used for manually setting values and parameters. Left Arrow: Shifts to the numbers on the left to set desired value. Down Arrow: One push will decrease 1 digit; A long press will decrease digits faster. Up Arrow: One push will increase 1 digit; A long press will increase digits faster. Cooling Key: Press and hold key for more than 4 seconds to control start/stop the cooling function. Circulation Key: Press to start/stop the circulation function.   Note: After all parameters have been input, press the cooling key for four seconds to being operation. Instructions Before Use The unit should be used under the following conditions: Place on a stable, non-combustible flat surface Ambient temperature of 5 ~ 35 ℃ Relative humidity ≤ 85% Atmospheric pressure: (86 ~ 106) KPa Altitude not higher than 2000 meters Power: 5L AC 110V±10%/60HZ, 20L: AC230V±10%/60HZ Keep away from any heat, corrosive gasses, strong vibration and electromagnetic sources. Provide a minimum of 300mm of space for proper ventilation (front and rear) Do not spill liquid anywhere other than the bath. When setting temperatures pay attention to freezing points (ethanol/ethylene glycol). When operating for the first time after replacing the heat transfer fluid there may be air trapped in the circulating pump, follow these instructions to purge: a. Disconnect the outlet line from the application NOTE: Fluid may leak from application, be ready with a bucket or plug the port. Hold the Outlet hose above the top of the bath so fluid does not drain out. b. Place the outlet hose into a clean collection bucket. c. Hold the outlet hose firmly so it does not fall out of the collection bucket d. Wearing safety glasses to shield any splashes, turn on the circulating function. e. After the liquid flow significantly increases, turn off the circulator. f. Reconnect the hoses to your application’s ports.        

Read more less

NEOCISION Cold Trap with Pump - ETL Rated - (-40c) Looking for a cold trap and small application chiller? The BVV™ CT40 features a 2-in-1 use with a cold trap function and built in circulating system for small batch temperature control.  Cold Trap Function Use the BVV™ CT40 to condense vapors down to -40°C before they reach your vacuum pump. This prolongs the life of the vacuum system, reduces the need to change oil frequently, and efficiently traps vapors otherwise lost to evaporation such as terpenes. Common applications include short path distillation, rotary evaporation, reactor setups, or any other application where volatile vapors can damage your vacuum pump. Chiller Function Use the BVV™ CT40 for small batch temperature control down to -40°C. Switch out the cold trap configuration with solid lid to turn your cold trap into a chiller. Common applications include condensing coils, small vessel setups, heat exchangers. Operating 2-in-1 Simultaneously Use the BVV™ CT40 as a cold trap and chiller. The unit can be used with the cold trap configuration and circulating function simultaneously. Commonly used as for chilling applications with no additional heat load.     BVV™-CTC40-WP Power Requirement AC 110V +/- 10% / 60Hz Relative Humidity < 85% Cooling Capacity 400W Refrigerant R404A Cold Trap Capacity 3 x 300ml Cold Trap Barb Dia. 10mm Reservoir Capacity 6.8L External Dimensions 305 x 485 x 635mm Weight 149 lbs     Call in to see how we can pair this unit with your setup Please Note: This device is designed for operation on its own independent circuit breaker. For best results, do not use this device on a breaker shared with other equipment. ***Notice to Customers: All units are inspected for broken glass or parts before the unit is shipped. If unit arrives damaged or glass is broken (this does not include minor imperfections or scuffs in glassware), Customer MUST contact BVV™ within 3 days of delivery to file a claim and receive a replacement part. If customer DOES NOT contact BVV™ within 3 days of delivery responsibility for replacement parts falls on the customer and they must pay for replacement pieces.*** ***Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.***

Read more less

NEOCISION Cold Trap - ETL Rated - (-80c) The BVV™ CT80 Cold Trap is used to condense vapors lost in vacuum applications before they reach the vacuum system. This prolongs the life of the vacuum system, reduces the need to change oil frequently, and efficiently traps vapors otherwise lost to evaporation such as terpenes. The CT80 model reaches a maximum temp of -80°c or -112F under vacuum and contains three traps for maximum efficiency and condensation of vapors. Place in-line between application and your vacuum system. Specifications: Temp Range: -112F to Ambient Internal Dimensions: 180mm Internal Diameter x 210mm Depth (Holds about 1.4 gallons) External Dimensions: 505 x 620 x 750mm Weight: 149lbs Stainless Steel Interior 3x Pyrex Glass Traps 110V Power Please Note: This device is designed for operation on its own independent circuit breaker. For best results, do not use this device on a breaker shared with other equipment.   ***Notice to Customers: All units are inspected for broken glass or parts before the unit is shipped. If unit arrives damaged or glass is broken (this does not include minor imperfections or scuffs in glassware), Customer MUST contact BVV™ within 3 days of delivery to file a claim and receive a replacement part. If customer DOES NOT contact BVV™ within 3 days of delivery responsibility for replacement parts falls on the customer and they must pay for replacement pieces.*** ***Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.***

Read more less

4.5 Cubic Feet Chest Freezer, Ultra Low Temperature The brand new BVV™ 4.5 cubic foot -86°C Ultra-Low Chest Freezer is a lab grade freezer at an affordable price with great temperature stability. It contains a dual independent refrigeration system inside and a SECOP compressor. This unit will run productively and efficiently, with a sleek design that will fit any lab or office setting. Every freezer unit includes various safety and protection features for both user and item safety. Features include high and low-temperature alerts and even a locking door. These compact chest freezers are appropriate for emergency clinics, creature cultivation, pharmaceutical organizations, and research foundations. They are intended for storage of pharmaceuticals, medication, immunizations, natural materials, testing reagents, research facility materials and can likewise be utilized to pre-chill solvents or winterize material. The freezer can fit up to two 5 gallon buckets inside. Key Features: 3 Ports to allow tubing or probes. SECOP Compressor Durable Powder Coated Exterior Stainless Steel Interior CFC-Refrigerant Free Power Failure and Over Temp Alarm High and Low Temp Alarms Large Digital Display Heavy Duty Rolling Casters Specifications Model Number BVV™-86C45 Voltage 115V / 60Hz Wattage 500w Capacity 128L / 33.8G Temperature Range -40°C to -86°C Exterior Dimensions 32.3" x 28" x 39.3" Interior Dimensions 25" x 17.5" x 18" Weight 197lbs

Read more less

BVV™ ULTRA-Low Chest Style Freezer (-60°C) 10.6 Cubic Feet   Single Compressor Model, Best Pick for Energy Savings!   The brand new BVV™ 10.6 cubic foot -60°C Ultra-Low Chest Freezer is a great all-around ultra-low temperature freezer at an affordable price with great temperature stability. This unit will run productively and adequately while brandishing a sleek design that will fit any lab or office setting.     These units are appropriate for emergency clinics, creature cultivation, pharmaceutical organizations, and research foundations. They are intended to store pharmaceuticals, medication, immunizations, natural materials, testing reagents, research facility materials and can likewise be utilized to pre-chill solvents or winterize material.    Key Features: Durable Powder Coated Exterior Aluminum Interior CFC-Refrigerant Free Large Digital Display Heavy Duty Rolling Casters 2 Wire Baskets for Extra Storage and Organization Specifications Model Number BVV™-60C106 Voltage 115V / 60Hz / 15A Capacity 10.6 Cu Ft. Temperature Range -30°C to -60°C Exterior Dimensions 50" x 30.1" x 34.8" Interior Dimensions 42.5" x 19.1" x 23.6" Weight 167lbs

Read more less

Neocision ULTRA-Low Chest Style Freezer with Touch Screen LCD  (-86°C) 16.2 Cubic Feet - ETL Rated The brand new Neocision ETL Rated 16.2 cubic foot -86°C Ultra-Low Chest Freezer is a lab grade freezer at an affordable price with great temperature stability. This unit will run productively and adequately while brandishing a sleek design that will fit any lab or office setting. Every unit accompanies various safety and protection features taking into consideration user and item safety. These highlights incorporate high and low-temperature alerts. These units are appropriate for emergency clinics, creature cultivation, pharmaceutical organizations, and research foundations. They are intended to store pharmaceuticals, medication, immunizations, natural materials, testing reagents, research facility materials and can likewise be utilized to pre-chill solvents or winterize material. Key Features: ETL Rated Durable Powder Coated Exterior Touch Screen LCD with Datalogging Capabilities Stainless Steel Interior CFC-Refrigerant Free Power Failure and Over Temp Alarm High and Low Temp Alarms Large Digital Display Heavy Duty Rolling Casters (3) 1" ID Ports for putting lines through the freezer Backup battery Included. Specifications Model Number NEO-86C162 Voltage 115V / 60Hz / 13A Wattage 1560w Capacity 16.2cu ft. / 458L / 121G Temperature Range -40°C to -86°C Exterior Dimensions 79-3/4" x 36" x 40" Interior Dimensions 51-1/2" x 23" x 25" Weight 529lbs Certification ETL Rated

Read more less

Neocision ULTRA-Low Chest Style Freezer with Touch Screen LCD  (-86°C) 25 Cubic Feet - ETL Rated The brand new Neocision ETL Rated 25 cubic foot -86°C Ultra-Low Chest Freezer is a lab grade freezer at an affordable price with great temperature stability. This unit will run productively and adequately while brandishing a sleek design that will fit any lab or office setting. Every unit accompanies various safety and protection features taking into consideration user and item safety. These highlights incorporate high and low-temperature alerts. These units are appropriate for emergency clinics, creature cultivation, pharmaceutical organizations, and research foundations. They are intended to store pharmaceuticals, medication, immunizations, natural materials, testing reagents, research facility materials and can likewise be utilized to pre-chill solvents or winterize material. Key Features: ETL Rated Durable Powder Coated Exterior Touch Screen LCD with Datalogging Capabilities Stainless Steel Interior CFC-Refrigerant Free Power Failure and Over Temp Alarm High and Low Temp Alarms Large Digital Display Heavy Duty Rolling Casters (3) 1" ID Ports for putting lines through the freezer Backup battery Included. Specifications Model Number BVV™-86C25 Voltage 115V / 60Hz / 15A Wattage 1800w Capacity 25cu ft. / 730L  Internal Dimensions 34.5" x 51.5" x 23.5" Exterior Dimensions 43" x 76" x 36" Temperature Range -40°C to -86°C Weight 700lbs Rating  ETL Rated

Read more less

Dry Ice Maker Machine Food Grade - Ultra Dense Block   This dry ice machine makes ice the way you want it! Using 2 tons of hydraulic force to compress the formed CO2 snow into a solid brick.  Other dry ice makers produce a loosely packed brick that sublimates quickly.  Our bricks take up to 1.5+ hours to sublimate.  All of the parts that touch liquid CO2 or ice are food-grade materials.   Use Specifications 20lbs of CO2 Retail ($1/lb) (*Bulk rates as low as $0.55/lb) $20 Input of CO2 (LBS) per Use 1.75 Dry Ice Output (LBS) per Use 0.38 Lbs of Dry Ice made from 20 lbs CO2 4.34 Cost per lb of Dry Ice made (approx) $4.61 Brick Formation Time (approx) 25 Seconds Connection for CO2 (includes gasket not shown in photo*) CGA 320   Additionally, this dry ice maker comes with these extra items... 1 white plastic shim 1 Black upper gasket 1-Year BVV Warranty Assembled in the USA by BVV  *Extreme cold temperatures will cause red paint to flake off of the jack over time. This is purely cosmetic.

Read more less

Cold Trap 2" Stainless Steel This Stainless Steel Cold is designed and intended for use with the Polyscience IP60 Cold Finger (Can also be used with dry Ice) to create a cold trap that can achieve extremely frigid temperatures. These cold traps have 2 1/4" FNPT ports with one having a dip tube to the bottom of the trap to achieve higher vapor condensing rates with the 2" Diameter Center opening for the IP60. This Cold trap also has an insulating vacuum jacket around the entire container to maintain the subzero temperatures and help achieve the maximum minimal temperature of the IP60. Unlike many cold Traps on the market, this one is also made out of 304 Stainless steel and the internal parts are resistant to most chemicals and easily cleaned due to the Tri-Clamp lid design. Specifications Material 304 Stainless Steel Temperature Rating -200 to 200°C Ultimate Vacuum <100millitorr / microns Cold Finger Internal Dimensions 1.85" x 11.75" (Fits Polyscience IP60) Trap Internal Dimensions 5.85" x 10" Outside Dimensions 8" x 14" x 15" (Includes jacket gauge and valve hardware) Weight 28LBS    

Read more less

10” X 10” KF25 Cold Trap Kit Cold traps are used in vacuum applications where contaminating vapors may be present, and a cold trap is required to assure vapors are condensed before reaching the vacuum pump. They can be used with any pump but are mostly used with rotary vane pumps. Protecting your pump will greatly increase the life of all your seals and internal components it will also assure that a full vacuum is pulled based on the pump’s capabilities. BVV’s 10”X10” KF25 Cold Trap features 2 qty. KF25 ports. The lower port is connected to the system that is under vacuum and the top to the vacuum pump. The KF25 allows for a larger bore and works great for high flow applications. This kit comes with 2 qty. KF25 rings and 2 qty. KF25 clamps ready to be connected in line with your setup. The internal pot is stainless steel and can hold 1.5 gallons which will hold the dry ice slurry or other method of getting cold. A silicone O-ring sits around the 1.5-gallon pot and creates a seal with the top of the 10”X10” base. For more specifications, please view table and diagrams below. Product Information Sheet  **This cold trap comes pre-tested to pull down to 30 microns** **This cold trap is rated for applications down to 30 microns. If your application requires a deeper vacuum, please DO NOT USE THIS COLD TRAP** Specifications    Model       CTRAP10X10-B       Material of Base and Internal Pot       Stainless Steel       Gasket Material       Silicone       Lid Material       Silicone + Glass    Vacuum Rating       30 microns       Weight       29lbs       Overall Height       11.5”       Overall Diameter (Including Ports)       14”       Cold Trap Surface Area       234.45 sq.in       Internal Pot Volume       1.5 gallons    Chemical Compatibility with Glass Lid    Ethanol       Excellent         Acetone       Good    Water       Excellent       Propylene Glycol       Excellent       Isopropyl Alcohol       Excellent    Chemical Compatibility with Silicone O-Ring and Lid Seal    Ethanol       Good       Acetone       Good       Pentane       Good       Hexane       Good       Heptane       Good      View of 10” x 10” Cold Trap

Read more less

1.5 Gallon Cold Trap (2QT Tank) Dry Ice, Liquid Nitrogen - W/GLASS LID    This is a complete Cold Trap and will come assembled for instant use. This Cold Trap is made of 304SS MADE IN USA, utilizing Glass lids for Durability, flexibility and Chemical Resistance to alcohol and solvents.   This system is Recommended to protect pump from condensable vapors.   This Trap comes with an industrial grade, heat cured silicone gasket designed only for our systems. There is nothing of equal quality in the market. The gasket itself is reversible (doubling the life of our system guaranteed) allowing customers to instantly take it off and flip it over. No adhesives are used! The system will maintain a vacuum seal only under vacuum. The vacuum pump will hold the interior 2 quart container for your Dry Ice Slurry in compression with the larger outer lid. The larger outer Lid will be held in compression with 1.5 gallon outer container.   The connections on both sides are 1/4" MJIC flares or 1/4" Barbs that will connect to 1/4" HVAC or FJIC stainless steel hose.    The Center Slurry Container has a lid for it, This lid simply helps prevent evaporation of your slurry.   Temperature rated for -100-160F   This Cold Trap comes assembled and includes:  (1) 1.5gl high strength Stainless steel outer container (made of solid 304 stainless made in USA) (1) 2q interior Slurry Container (made of solid 304 stainless made in USA) (2) 1/2" thick clear Glass lids (2) Industrial grade silicone gasket (1) 1/4" HVAC Hose 5' Can withstand max working temps of 392F gasket only 60A durometer density (1) Max vacuum -29.5inHg (+/-.5Hg) (2) 1/4" MJIC or Barb Fittings    Outside Container Internal Dimensions: 7.25" Diameter X 8.25" Tall    To help remove condensable vapors, or when liquid nitrogen traps are not practical, our Cold Trap is the best option for preventing vapors from getting into your vacuum pump and contaminating it. This 1.5 gallon trap uses Glass lids for durability, flexibility, and chemical resistance. The system doesn’t use adhesives, and comes standard with a reversible gasket for enhanced quality that doubles its life.   Made in the USA, the BVV™ Cold Trap comes with all parts pre-assembled, so you can get to work straight out of the box.   Inside Container Internal Dimension: 4.75 Diameter by 6.5 Tall

Read more less

1.5 Gallon Cold Trap (2QT Tank) Dry Ice, Liquid Nitrogen (Comes with 2 Year Limited warranty)   This is a complete cold trap and will come assembled for instant use. This cold trap is made of 304SS MADE IN USA, utilizing Polycarbonate lids for durability, flexibility and chemical resistance to Ethanol and Isopropyl (not compatible with Acetone).   This system is recommended to protect pump from condensable vapors.   This trap comes with an industrial grade, heat cured silicone gasket designed only for our systems. There is nothing of equal quality in the market. The gasket itself is reversible (doubling the life of our system guaranteed) allowing customers to instantly take it off and flip it over. No adhesives are used! The system will maintain a vacuum seal only under vacuum. The vacuum pump will hold the interior 2 quart container for your dry ice slurry in compression with the larger outer lid. The larger outer lid will be held in compression with 1.5 gallon outer container.   The connections on both sides are 1/4" MJIC flares or 1/4" Barbs that will connect to 1/4" HVAC or FJIC stainless steel hose.    The center slurry container has a lid - this lid simply helps prevent evaporation of your slurry.   Temperature rated for -100-160F   This cold trap comes assembled and includes:  (1) 1.5gl high strength stainless steel outer container (made of solid 304 stainless made in USA) (1) 2q interior slurry container (made of solid 304 stainless made in USA) (2) 1/2" thick clear polycarbonate lids (2) industrial grade silicone gasket (1) 1/4" HVAC hose 5' Can withstand max working temps of 392F gasket only 60A durometer density (1) max vacuum -29.5inHg (+/-.5Hg) (2) 1/4" MJIC or Barb Fittings    Outside container internal dimensions: 7.25" diameter X 8.25" tall    To help remove condensable vapors, or when liquid nitrogen traps are not practical, our cold trap is the best option for preventing vapors from getting into your vacuum pump and contaminating it. This 1.5 gallon trap uses polycarbonate lids for durability, flexibility, and chemical resistance. The system doesn’t use adhesives, and comes standard with a reversible gasket for enhanced quality that doubles its life.   Made in the USA, the BVV™ Cold Trap comes with all parts pre-assembled, so you can get to work straight out of the box.   Inside container internal dimension: 4.75" diameter by 6.5" tall

Read more less

BVV™ Dewar Glass Cold Trap This dewar style glass is designed for maximum vapor condensation and it also has a 24/40 bottom joint and (2) GL-14 8mm Hose Barbs *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement.

Read more less

BVV™ Glass Cold Trap - Ribbed This dewar style glass is designed to increase surface area for maximum vapor condensation and it also has 24/40 or 34/45 jointed connections to increase vapor flow. Note: The bottom joint will always be 24/40. *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement.

Read more less

Dewar Style Glass Cold Trap The Dewar Style Glass Cold Trap with GL-14 Barb Fittings allows the user to load dry ice into the inner portion of the cold trap from the top to allow maximum condensation temperatures. This protects your vacuum pump and captures any vapors that were lost during evaporation or distillation. Made in the USA. Dewar Style Glass Cold Traps includes the following: Metal Keck Clip Boss Head Lab Stand Chain Clamp 250ml Round Bottom Flask 24/40 Joint 250-500ml Cork Stand Specifications: USA Made 24/40 Male Ground Joint GL-14 8mm Barb Connections OD = 3.8" ID = 2.75" Height = 14.75" *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**

Read more less

Cold Trap O-ring for Inner Vessel This is a replacement O-ring gasket for the inner vessel of the cold trap to create a seal between the lid and dry ice container. Material: Silicone  

Read more less

Replacement Trap for CT40 and CT80 Cold Traps This is a replacement glass trap for the CT40 and CT80 model cold traps. The trap fits in the lid of the cold traps and is suspended in the chilling fluid. Specifications: 3/8" Hose Barb Connection 34/45 Joint 2" Diameter x 10" Height Material: Boro 3.3 *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement.  **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**

Read more less

Haier Ultra Low Energy Smart Frequency Conversion ULT Freezer 579L (20.5cf)     Haier Biomedical Ultra Low Temperature Freezer Key Design Features Microprocessor-controlled system designed for controllable range of -40 °C to -86 °C for cabinet space with 1 °C increment Large LCD touchscreen for cabinet temperature, set temperature, ambient temperature, and input voltage Settable high temperature and low temperature alarms Automatic clean-filter alarm and sensor error alert Adjustable storage shelf height Can be connected with network, and remote alarm systems Optional temperature recorder, storage racks and storage boxes     Field Proven Reliability Refrigeration system designed and manufactured with best known practice, and components with highest possible quality Reliability test performed and passed on all models including aging test on control electronics at 85 °C and 85% humidity environment Unique insulated inner door design for four separate storage compartments to minimize frost buildup inside the chamber Specialized control system design for a well-balanced operation of cascade refrigeration system z Safety Equipped with a complete alarm system with optional remote network monitoring system UL, ENERGY STAR and CE certified for application safety Dual independent refrigeration systems, making the samples safer, The dual refrigeration systems run independently and alternately, and both of them can reach up to -80 °C through independent refrigeration. Malfunction alarms including high and low temperature, power outage, sensor errors, high voltage and low voltage, clean-filter, and extremely high ambient, door ajar feature standard Capable of producing two types of alarm outputs: audible buzzer and visible flashing light Multiple built-in system protection features including user-settable protection code for controls, user settable delay to start, voltage compensation system, and protection against extreme high voltages USB port for temperature data downloading Safety padlock compatible on outer door   Installation and Application Wide range operating voltage system from 115V to 230V designed to allow units installed in areas with poor voltage condition Suitable for 10 °C to 32 °C Ambient temperature Input voltage and ambient temperature shown simultaneously for ease of monitoring environmental conditions Freezer design for global installations Robust door latch designed for secure door closing and compact casters for ease of maneuvering Low Sound Level Freezer chassis designed to absorb vibration and sound Energy Saving Unique door seal and breaker design for the minimum loss of cold temperature during a door opening High performance VIP insulation panels to minimize cabinet heat gain and to improve temperature stability Patented cabinet insulation system designed for optimal performance of cold storage temperature and minimal frost buildup Condenser fan intelligently start-stop to reduce power consumption Unique design of independent insulated inner door systems for independent access of storage space to provide the maximum protection of stored samples and save energy       Model DW-86L579BPT Technical Data Cabinet type Upright Climate Class N Cooling Type Direct cooling Defrost Mode Manual Refrigerant HC Noise((dB(A)) 43.5 Performance Cooling Performance(oC) -86 Temp Range(oC) -40~-86 Control Controller Microprocessor Display LCD Electrical Data Power Supply(V/HZ) 100～230/50/60 Power (W) 1100 Electrical Current(A) 6 Dimensions Capacity(L/Cu.Ft) 579/20.4 Net/Gross Weight (approx) 325/355 716.5/782.6 Interior Dimension (W*D*H) 620*716*1310 24.4*28.2*51.6 Exterior Dimension (W*D*H) 895*998*1980 35.4*39.3*78.0 Packing Dimension (W*D*H) 950*1055*2150 37.4*41.5*84.6 Container Load(20'/40'/40'H) 12/24/24 Functions Remote Alarm Y High/Low Temp Y Hot Condenser Y Power Failure Y Sensor Error Y Low Battery Y High Ambient Temp Y Door Ajar Y Accessories Caster Y Foot Y Test Hole Y/2 Shelves/ Inner Doors 3/4 USB Interface Y 5V Power Supply Port Y Temp Recorder Optional 485 Port Standard CO2 Backup System Optional LN2 Backup System Optional Others Certificate CE、UL

Read more less

Ultralow Freq. Conversion -86C Freezer, Energy Star 959L (34cf) 208-230V/60Hz     Haier Biomedical Ultra Low Temperature Freezer Key Design Features Microprocessor-controlled system designed for controllable range of -40 °C to -86 °C for cabinet space with 1 °C increment Large LCD touchscreen for cabinet temperature, set temperature, ambient temperature, and input voltage Settable high temperature and low temperature alarms Automatic clean-filter alarm and sensor error alert Adjustable storage shelf height Can be connected with network, and remote alarm systems Optional temperature recorder, storage racks and storage boxes     Field Proven Reliability Refrigeration system designed and manufactured with best known practice, and components with highest possible quality Reliability test performed and passed on all models including aging test on control electronics at 85 °C and 85% humidity environment Unique insulated inner door design for four separate storage compartments to minimize frost buildup inside the chamber Specialized control system design for a well-balanced operation of cascade refrigeration system       Safety Equipped with a complete alarm system with optional remote network monitoring system UL, ENERGY STAR and CE certified for application safety Dual independent refrigeration systems, making the samples safer, The dual refrigeration systems run independently and alternately, and both of them can reach up to -80 °C through independent refrigeration. Malfunction alarms including high and low temperature, power outage, sensor errors, high voltage and low voltage, clean-filter, and extremely high ambient, door ajar feature standard Capable of producing two types of alarm outputs: audible buzzer and visible flashing light Multiple built-in system protection features including user-settable protection code for controls, user settable delay to start, voltage compensation system, and protection against extreme high voltages USB port for temperature data downloading Safety padlock compatible on outer door     Installation and Application Wide range operating voltage system from 115V to 230V designed to allow units installed in areas with poor voltage condition Suitable for 10 °C to 32 °C Ambient temperature Input voltage and ambient temperature shown simultaneously for ease of monitoring environmental conditions Freezer design for global installations Robust door latch designed for secure door closing and compact casters for ease of maneuvering Low Sound Level Freezer chassis designed to absorb vibration and sound Energy Saving Unique door seal and breaker design for the minimum loss of cold temperature during a door opening High performance VIP insulation panels to minimize cabinet heat gain and to improve temperature stability Patented cabinet insulation system designed for optimal performance of cold storage temperature and minimal frost buildup Condenser fan intelligently start-stop to reduce power consumption Unique design of independent insulated inner door systems for independent access of storage space to provide the maximum protection of stored samples and save energy       Model DW-86L729BPT Technical Data Cabniet type Upright Climate Class N Cooling Type Direct cooling Defrost Mode Manual Refrigerant HC Noise((dB(A)) 43.5 Performance Cooling Performance(oC) -86 Temp Range(oC) -40~-86 Control Controller Microprocessor Display LCD Electrical Data Power Supply(V/HZ) 208～230/50/60 Power (W) 1100 Electrical Current(A) 7 Dimensions Capacity(L/Cu.Ft) 959/33.9 Net/Gross Weight (approx) 450/485 992.1/1069.2 Interior Dimension (W*D*H) 1016*716*1310 40.0*28.2*51.6 Exterior Dimension (W*D*H) 1296*998*1980 51.0*39.3*78.0 Packing Dimension (W*D*H) 1365*1105*2150 53.7*43.5*84.6 Container Load(20'/40'/40'H) 8/16/16 Functions Remote Alarm Y High/Low Temp Y Hot Condenser Y Power Failure Y Sensor Error Y Low Battery Y High Ambient Temp Y Door Ajar Y Accessories Caster Y Foot Y Test Hole Y/2 Shelves/ Inner Doors 3/4 USB Interface Y 5V Power Supply Port Y Temp Recorder Optional 485 Port Standard CO2 Backup System Optional LN2 Backup System Optional Others Certificate CE、UL

Read more less

Haier Ultralow -86C freezer,490L(17.3cf), 220V/60Hz   This product line is designed and manufactured for long term storage of various biological products, including viruses, germs, erythrocytes and leucocytes. Applications can be found in blood banks, hospitals, epidemic prevention services, research institutes, biological engineering institutes, laboratories in electronic and chemical plants.  Note: All JA Models are configured as 220V/60Hz       Key Design Features Microprocessor-controlled system designed for controllable range of -40°C to -86°C for cabinet space with 1°C increment  Large LED display for cabinet temperature, set temperature, ambient temperature, and input voltage Settable high temperature and low temperature alarms Automatic clean-filter alarm and sensor error alert Adjustable storage shelf height Optional temperature recorder, storage racks and storage boxes       Field Proven Reliability  Unique insulated inner door design for four separate storage compartments to minimize frost buildup inside the chamber Specialized control system design for a well-balanced operation of cascade refrigeration system Positive field proven reliability record       Safety  Malfunction alarms including high and low temperature, power failure, sensor error, clean -filter, and extremely high ambient  Capable of producing two types of alarm outputs: audible buzzer and visible flashing light Multiple built-in system protection features including user-settable protection code for controls, user settable delay to start, voltage compensation system, and protection against extreme high voltages Door open feature standard and USB port for temperature data downloading standard on upright models  Remote alarm contacts       Installation & Application Wide range operating voltage system from 185V to 260 V designed to allow units installed in areas with poor voltage condition Suitable for 10°C to 32°C ambient temperature  Input voltage and ambient temperature shown simultaneously for ease of monitoring environmental conditions  Robust door latch designed for secure door closing  Compact casters for ease of maneuvering   .   Low Sound Level Specialized refrigeration system design using whisper quiet fan and compressors Freezer chassis designed to absorb vibration and sound       Energy Saving Unique door seal design for the minimum loss of cold temperature during a door opening High performance VIP insulation panels to minimize cabinet heat gain and to improve temperature stability Patented cabinet insulation system designed for optimal performance of cold storage temperature and minimal frost buildup  Unique design of independent insulated inner door systems for independent access of storage space to provide the maximum protection of stored samples       Model DW-86L338J Technical Data Cabinet Type Upright Climate Class N Cooling Type Direct Cooling Defrost Mode Manual Refrigerant HC Noise Lever(dB) 50 Performance Cooling performance (°C) -86 Temperature Range(°C) -40~-86 Control Controller Microprocessor Display LED Electrical Data Power Supply (V/Hz) 220/60 Power 900 Electrical Current (A) 8 Functions High/Low Temperature Y Remote Alarm Y Hot Condenser Y Power Failure Y Sensor Error Y Low Battery Y High Ambient temp Y Door Ajar Y Accessories Caster Y Foot Y Test Hole Y/2 Shelves/Inner Doors 3/4 Temperature Recorder Optional USB Interface Y Rs232?485 Interface Optional CO₂ Backup System Optional LN₂ Backup System Optional Racks & Boxes Optional Dimensions Capacity(L/Cu.Ft) 490/17.3 Net/Gross Weight(approx) 295/335(kg) 650.4/738.5(lbs) Interior Dimensions(W*D*H) 590*630*1310(mm 23.2*24.8*51.6(in Exterior Dimensions(W*D*H) 860*900*1980(mm) 33.9*35.4*78.0(in Packing Dimensions(W*D*H) 875*970*2010(mm) 34.5*38.2*79.1(in) Container load (20'/40'/40'H 12/24/24 Others Certificate CE

Read more less

Neocision ULTRA-Low Upright Style Freezer with Touch Screen LCD  (-86°C) 17.3 Cubic Feet - ETL Rated The BVV™ Neocision Freezers offer optimal temperature control conditions to use in laboratories and medical facilities. The freezers have a quiet operating noise of less than 53 decibels. This freezer has a user friendly touch screen that can be used to monitor many different aspects of the internal systems. The screen will display any errors such as temperature faults or power faults. There is a backup battery that will keep the screen operational though a facility power outage, and it will display the internal temperatures. This information can help the user input dry ice or liquid nitrogen to assist in cooling sensitive materials through a prolonged power outage. The internal chamber has 4 sections that can be used individually or the shelves can be removed or adjusted to fit larger items. Features: Backup Battery Data Logging Gasket Heating Locking Handle Vent Port Interior Chamber Probe High Condenser Temperature Alarm Power Failure Alarm Temperature Sensor Failure Alarm Low Battery Alarm High/Low Temperature Alarm Door Alarm Specifications: Model NEO-86L490 Temperature Range (°C) -50 ~ -86 Temperature Uniformity (°C) ≤6 Cooldown time (hours) ≤6 Capacity (ft^3) 17.3 Exterior Dimensions (LxWxH) (in) 35.8 x 36.5 x 78.3 Interior Dimensions (LxWxH) (in) 23.1 x 25 x 51.5 Door Opening (LxH) (in) 23.1 x 51.5 Insulation thickness (in) 5 Interior Material Stainless Steel Door Sections 4 Shelves 3 Levels 4 Refrigerant Type Non HCFC Voltage 220V AC Power 1500 W Weight (lbs) 732

Read more less

Neocision ULTRA-Low Upright Style Freezer with Touch Screen LCD  (-86°C) 27 Cubic Feet - ETL Rated The BVV™ Neocision Freezers offer optimal temperature control conditions to use in laboratories and medical facilities. The freezers have a quiet operating noise of less than 53 decibels. This freezer has a user friendly touch screen that can be used to monitor many different aspects of the internal systems. The screen will display any errors such as temperature faults or power faults. There is a backup battery that will keep the screen operational though a facility power outage, and it will display the internal temperatures. This information can help the user input dry ice or liquid nitrogen to assist in cooling sensitive materials through a prolonged power outage. The internal chamber has 4 sections that can be used individually or the shelves can be removed or adjusted to fit larger items. Features: Backup Battery Data Logging Gasket Heating Locking Handle Vent Port Interior Chamber Probe High Condenser Temperature Alarm Power Failure Alarm Temperature Sensor Failure Alarm Low Battery Alarm High/Low Temperature Alarm Door Alarm Specifications: Model NEO-86L770 Temperature Range (°C) -50 ~ -86 Temperature Uniformity (°C) ≤6 Cooldown time (hours) ≤8 Capacity (ft^3) 27 Exterior Dimensions (LxWxH) (in) 43 x 41.5 x 78.3 Interior Dimensions (LxWxH) (in) 30.7 x 29.9 x 51.5 Door Opening (LxH) (in) 30.7 x 51.5 Insulation thickness (in) 5 Interior Material Stainless Steel Door Sections 4 Shelves 3 Levels 4 Refrigerant Type Non HCFC Voltage 220V AC Power 1800 W Weight (lbs) 1080

Read more less

Discover the Cold Shot Chillers® advantage.  Crafted for reliability and user-friendly operation,  These portable air-cooled chillers are proudly manufactured in the USA, utilizing proven components and backed by round-the-clock support from a network of technicians in the US. Engineered for a lifetime of service, these chillers ensure precise temperature control. Robust compressors paired with a generous reservoir deliver impressive cooling capacities, keeping your operations smooth even during the hottest months. Choose Cold Shot Chillers® for a reliable, long-lasting cooling solution. Key Features: Integrated Controls: PLC controlled with self-diagnostics. WIFI/LAN/LTE connectivity for predictive maintenance through Guardian™ app. Email/text notifications for predictive maintenance milestones, technical alarms, fault codes, and alerts. Quality Construction: Copeland Scroll technology for efficiency. Stainless Steel/Copper Braze Plate for durability. External Brass Service Valves for easy maintenance. Large Copper Condensing Coil with Aluminum Fins or Micro Channel for effective cooling. Powder-Coated, Heavy-Gauge Steel Cabinet for rugged protection. Additional Specifications: Rugged Stainless Steel Centrifugal Pumps for high flow and dependability. Oversized Magnetic Contactors for longevity. Lifetime Warranty for peace of mind. Benefits: Long Life – Dependable – Economical to Operate. Compact Efficiency for space-saving installations. Easy Maintenance and Repair for user-friendly operation. Rugged Protection while allowing for easy maintenance and wash down. High Flow – Long Life – Dependable performance. Rugged Dependability with a Lifetime Warranty. Specifications: 10 tons (120,000 BTU/35.16KW) 41 Gallon Stainless Steel Reservoir Tank with Lid This Low Temp Model has a leaving fluid temperature range of 20F-70F/-6C-21C. 1.25” MNPT Inlet and Outlet Stainless Steel 1.5 HP Centrifugal Pump outputs 40 GPM at 30 PSI Single Phase (230V/1P/60HZ/81.5A) and Three Phase (230V/3P/60HZ/63.9A) power available Casters Included (two swivel locking and two fixed) Large Reservoir easily filled from outside, and level indicated with sight gauge 1-Year Parts Warranty 5-Year Warranty on Compressor Welded steel powder-coated frame and full metal cabinet with copper piping connections Digital Temperature controller with Self-Diagnostic control system Rugged Protection, while still easy to maintain and Wash Down High Flow Pump, Long Life, Dependable units! Stainless Steel Plate Evaporators Vacuum brazed with Copper Dependable Copeland Welded hermetic Scroll Compressors 61.5"x43"x66.6" 1100 lb UL Certified Please Note:  This unit REQUIRES  a qualified electrician to wire the necessary plug to the cord. *Please Note: This unit is rated for indoor use only. If you require a chiller rated for outdoor use, please contact our customer service department to request a special order. Cold Shot Chillers are available suitable for outdoor use with ambient temperature ratings as low as -20F.

Read more less

Discover the Cold Shot Chillers® advantage.  Crafted for reliability and user-friendly operation,  These portable air-cooled chillers are proudly manufactured in the USA, utilizing proven components and backed by round-the-clock support from a network of technicians in the US. Engineered for a lifetime of service, these chillers ensure precise temperature control. Robust compressors paired with a generous reservoir deliver impressive cooling capacities, keeping your operations smooth even during the hottest months. Choose Cold Shot Chillers® for a reliable, long-lasting cooling solution. Key Features: Integrated Controls: PLC controlled with self-diagnostics. WIFI/LAN/LTE connectivity for predictive maintenance through Guardian™ app. Email/text notifications for predictive maintenance milestones, technical alarms, fault codes, and alerts. Quality Construction: Copeland Scroll technology for efficiency. Stainless Steel/Copper Braze Plate for durability. External Brass Service Valves for easy maintenance. Large Copper Condensing Coil with Aluminum Fins or Micro Channel for effective cooling. Powder-Coated, Heavy-Gauge Steel Cabinet for rugged protection. Additional Specifications: Rugged Stainless Steel Centrifugal Pumps for high flow and dependability. Oversized Magnetic Contactors for longevity. Lifetime Warranty for peace of mind. Benefits: Long Life – Dependable – Economical to Operate. Compact Efficiency for space-saving installations. Easy Maintenance and Repair for user-friendly operation. Rugged Protection while allowing for easy maintenance and wash down. High Flow – Long Life – Dependable performance. Rugged Dependability with a Lifetime Warranty. Specifications: 5 tons (60,000 BTU/17.5KW) 25 Gallon Stainless Steel Reservoir Tank with Lid This Low Temp Model has a leaving fluid temperature range of 20F-70F/-6C-21C. Rated to 0°F ambient temperature* 1” MNPT Inlet and Outlet Stainless Steel 1 HP Centrifugal Pump outputs 30 GPM at 30 PSI Single Phase (230V/1P/60HZ/47.2A) and Three Phase (230V/3P/60HZ/35.1A) power available Casters Included (two swivel locking and two fixed) Large Reservoir easily filled from outside, and level indicated with sight gauge 1-Year Parts Warranty 5-Year Warranty on Compressor Welded steel powder-coated frame and full metal cabinet with copper piping connections Digital Temperature controller with Self-Diagnostic control system Rugged Protection, while still easy to maintain and Wash Down High Flow Pump, Long Life, Dependable units! Stainless Steel Plate Evaporators Vacuum brazed with Copper Dependable Copeland Welded hermetic Scroll Compressors 50.5"x38.5"x57" 500 lb UL Certified Please Note:  This unit REQUIRES  a qualified electrician to wire the necessary plug to the cord. *Please Note: This unit is rated for indoor use only. If you require a chiller rated for outdoor use, please contact our customer service department to request a special order. Cold Shot Chillers are available suitable for outdoor use with ambient temperature ratings as low as -20F.

Read more less

Economy Recirculating Heater Kit The Economy Recirculating Heater Kit is designed to provide efficient heating and circulation at an affordable price. The kit includes a submersible water pump for fluid circulation, an LX or MX immersion heater, and all tubing and hose clamps needed to pair with your system. The tubing is 1/2" ID x 5/8" OD and the pump fitting is 1/2". The pump will circulate up to 594 GPH. Economy Recirculating Heater Kit Includes: Polyscience LX or MX Immersion Circulator EcoPlus Eco 633 Fixed Flow Submersible/Inline Pump 594 GPH 5 Gallon Aluminum Pot 10 Feet of 1/2" Silicone Tubing 10 Pack of Adjustable Stainless Steel Tubing Clamps

Read more less

BVV™ Neocision 5 Liter Heated Circulator - ETL Listed The brand new BVV™ Neocision 5 Liter Heated Circulator - ETL Listed brings very stable temperature control and lab grade quality at a great price. This refrigerated circulator has a durable powder coated exterior with a stainless steel top, stainless steel interior and a large control head with digital display. BVV Neocision 5 Liter Heated Circulator - ETL Listed Key Features: ETL Certified Digital Control Head with Large Display Corrosion Resistant Stainless Steel Top and Interior 135°C Max Temperature Rubber Feet for Vibration Dampening and Noise Reduction 5L Internal Reservoir Capacity Small Table Top Design Specifications Model Number NEO-7H Voltage 115V / 60Hz Wattage 1000w Reservoir Capacity 5L/ 1.32G Temperature Range RT+5°C to 135°C Internal Dimensions 5.9" x 6.3" x 5.9" External Dimensions 13-1/4" x 7-3/4" x 15" Display Resolution 0.1°C Temperature Stability +/- 0.1°C Flow Rate 8L/min

Read more less

BVV™ Neocision 19 Liter Heated Circulator - ETL Listed   The brand new BVV™ Neocision 19 Liter Heated Circulator - ETL Listed brings very stable temperature control and lab grade quality at a great price. This refrigerated circulator has a durable powder coated exterior with a stainless steel top, stainless steel interior and a large control head with digital display. This high powered laboratory heater is great for extraction or distillation applications!   Key Features: ETL Certified Digital Control Head with Large Display Corrosion Resistant Stainless Steel Top and Interior 220°C Max Temperature Rubber Feet for Vibration Dampening and Noise Reduction 19L Internal Reservoir Capacity Small Table Top Design Side drain valve for water bath 1/2" Male NPT attachments   Technical Indicators Index NEO-19H Power Supply Voltage AC220V 60Hz Input Power (W) 4100 Temperature Control Range (C°) RT+20 ~ 220 C° Temperature Fluctuation  (C°) ±0.1 Pump Flow  (Lmin) 10(water ) Filling Volume (L) 22.5 Bath Opening Size (mm) 200 x 120 Dimensions (W x D x H) (mm) 330 x 300 x150

Read more less